| New
Product :: 07-08 Tahoe & Yukon 5.3L Headers, Exhaust
and Ignition Wires |

Click to enlarge
|
The
new Chevy Tahoes and GMC Yukons are out and
are turning heads with fresh new looks inside and
out. Their updated Vortec 5.3L V8s are putting out
more power with greater efficiency too. JBA didn't
waste
any time on developing a performance package with
headers, exhaust systems and ignition wires to get
even more
power and better
sound
out of the trusted Vortec engines. The JBA Cat4ward®
headers and JBA exhaust
system bolt up without modification for the perfect
combination of power and sound with reduced backpressure
and increased flow. Add a set of new JBA Powercables™
to get more spark energy for even greater gains.
Get
the
complete system for your new SUV and experience the
JBA difference. |
| JBA
Cat4ward® Headers:: |

Click to enlarge
|
At
the heart of your new SUV is Chevy's dependable
and powerful Vortec V8. New for 2007 and 2008 is Active
Fuel Management to help save some money at the
pump. These small blocks are capable of getting
most jobs done
but
when
the load gets heavy the factory cast
manifolds get in the way of performance and efficiency.
JBA's Cat4ward® Headers designed for the Vortec
V8 open up the breathing on your truck with high-flowing
mandrel-bent 1-5/8" primary tube that merge
into JBA's patented Firecone® merged collector.
By reducing back pressure and turbulence in the
exhaust,
the JBA headers free up torque, horsepower and
efficiency lost in the factory set-up. Get as much
as 14+ hp and 21 lb-ft of torque at the tires.
These headers also feature ultra thick 3/8" laser-cut
flanges
and
are available in a variety of finishes to fit your
specific needs. Each kit includes high quality
hardware and thorough instructions for a professional
bolt-on installation. |

Up to and including model year 2006
The product accompanying this document has been granted a California Air Resources Board (CARB) exemption, an “E.O.” number, or is a direct or consolidated replacement part. It is 50-state legal, per the manufacturer’s application guide.
|

Model year 2007 - 2011
*The product accompanying this document is legal only for off-highway use (except in California or states that have adopted California emission standards), racing use or for use on pre-emission-controlled motor vehicles/motor vehicle engines (pre-1974 domestic vehicles certified to California standards, pre-1974 domestic vehicles certified to federal standards and all pre-1974 foreign vehicles), per the manufacturer’s application guide. |
| ::Header
Features:: |
- 3/8" thick laser-cut flanges
- Stainless steel primary tubes
- Patented JBA Firecone® merge collector
- JBA sealing dome
- Premium quality hardware and gaskets included
- Will not void factory warranty
- Optional ceramic coating (thermal barrier)
|
|
| ::Header
Benefits:: |
- Increase
hp & torque throughout RPM range
- Improved
throttle response
- Reduced
under hood temperature
- Increased
passing power
- Increased
low-end torque
- Makes engine more sensitive to other modifications
(intake, chip, supercharger, etc.)
- Improved
engine compartment appearance
- Improved
fuel economy*
* results may vary |
|
| |
| JBA
PowerCables™ Ignition Wires:: |

8mm JBA PowerCables™ p/n 0807.
|
When
upgrading the performance of your SUV, you
will want to upgrade your ignition wires to a set of
JBA PowerCables™. Each set is custom tailored
to your specific application so you get a perfect fit
every time. JBA's performance ignition wires feature
ultra-low resistance
wire-wound
mag conductors that allow more spark energy to reach
the spark plug without electronic interference. JBA
Powercables™ come with 100% silicone jackets
for great resistance to high heat as well as abrasion
and tears.
The high heat boots give plenty of clearance for routing
around the headers. Sport
Truck magazine tested
these wires and found they were less than 1/2 the resistance
of the factory wires. The editors at Car
Craft made an extra 5 hp
on a
project engine with a set of 9mm JBA PowerCables™.
Installing a set of these wires is easy to do on the
Vortec engines and they look great under the
hood. |
| ::Ignition
Wires:: |
Application |
Part No. |
07-08,
5.3 V8 - Red |
0807 |
07-08,
5.3 V8 - Blue |
08079 |
|
| JBA
Performance Exhaust Systems:: |

Click to enlarge
|
Most
SUV owners probably know what it's like when the
hill is steep and your V8 is running
wide
open
to keep up with traffic. JBA's exhaust
systems
give the new 5.3L small block engine under
your
hood
a less restrictive path to expel spent gasses freeing up extra ponies. This
is one of the easiest ways to increase horsepower
and
torque
on
your
truck.
JBA's new exhaust system for the 2007 Tahoe and Yukon
is engineered and tuned to deliver maximum performance
gains throughout
the
RPM
range without annoying interior resonance. These JBA
kits feature 3" mandrel-bent stainless steel tubing,
a fully welded stainless steel high flow JBA muffler,
factory style exhaust
hangers,
and
a great looking 3-1/2" polished and chrome plated
stainless steel rolled tip. Power. Sound. Quality.
JBA has it
all. |
| ::07-08 Tahoe/Denali
Exhaust Systems |
Application |
Part
No. |
07-08,Tahoe
/ Yukon, 5.3L, 2/4WD, 3" stainless,
side exit, 3-1/2" JBA S/S tip |
40-3043 |
|
| ::Exhaust
Features:: |
- Aggressive sound without annoying interior resonance
- Smooth flowing mandrel-bent tubing
- Complete stainless steel construction
- High flow stainless steel JBA muffler
- Polished stainless steel chrome plated 3-1/2"
rolled lip exhaust tip with JBA logo
- Easy bolt-on installation
- Stainless steel hardware
- O.E. style exhaust hangers
- Will not void factory warranty
|
|
::Dealer locator::
Find your nearest distributors
::Shop Online::
For a listing of online distributors |